Euronova washing machines (Eurosoba) are assembled in Austria, so they are distinguished by their enviable quality and excellent technical characteristics. In Russia they are better known as “Baby from Porsche”.
Euronov cars are usually designed for 14 years of operation. 80% of all nodes are developed by the manufacturer - Eudora Gmbh.
AGRs are individually tested at every stage of production. If they break, it is usually due to violations of the operating rules and external factors:
- low quality water;
- voltage drops in the network;
- low quality powders.
Today we will consider the main malfunctions of this brand and tell what to do if the Euronov (Eurosoba) washing machine breaks down.
SM Euronova shows the error code
Thanks to the high technology of machines equipped with a self-diagnosis system, users will find out about malfunctions right there - by fault codes.
Consider the error codes that the Euronova machine gives, and their meanings:
- The door lock is broken, or the microswitch is out of order. The first thing you can do in this situation is to check whether the hatch is tightly closed. After check the health of the castle.
- Waste water discharge does not work. Most often, the impeller of the pump is to blame. It can be blocked due to scale, deposits of washing powder and blockages in the sewer system.
- Water is not poured. Reasons: the water supply valve is blocked, insufficient pressure in the water supply, clogged water inlet filter, breakdown of the inlet valve.
- Occurs when the residual water level exceeds normal. The tightness of the water inlet valve may be impaired.
- Indicates a breakdown of the temperature sensor (thermistor).
- The code indicates the absence of heating water. The electric heater (TEN) could fail.
- This error occurs if too much water has entered the tank.
- Motor or tachometer error (tachometer, tachogenerator).
- The code indicates a thyristor breakdown.
- It is displayed when the interlock circuit is faulty.
- A rare mistake means a fault in the pump circuit.
Euronov's washing machine leaks
If the washer began to leak during washing, you can figure out the problem and carry out repairs yourself. Causes of leaks:
- damage to the cuff of the hatch;
- household cleaning products of poor quality;
- blockages in the system;
- breakdown or crack in the tank;
- breakage of the filler valve, water level switch and other details.
Important! Do not operate the machine if it is flowing. If you find a leak, immediately disconnect the CM from the network until you can fix the problem.
This breakdown is most characteristic of the models Euronova 600, Euronova 800, Euronova 1000.
In this case, do-it-yourself repair is to eliminate the causes of blockages that could cause a leak.
Checking Euronov hoses for blockages
- Check the drain hose. Small items falling out of the pockets of clothes during washing can clog into it.
- Check the hatch. It may be broken latch or damaged rubber band - cuff. If the cuff is clogged - clean it, if there is slight damage - you can seal it with a rubber patch, and if the damage to the cuff is too strong, replace it.
SM Eurosoba (Euronova) does not pick up water
At startup, the machine may not draw water, so it will not start to wash. This can mean either a software error or a failure of one of the nodes.
Try to figure out for yourself what triggered the failure:
- There may be no water in the water supply system. To check this, simply open the faucet in the bathroom or in the kitchen.
- There is water, but the pressure in the system is not enough to create a normal pressure. The machine either does not collect water at all, or does it too slowly.In this and the previous case, you should wait until the water supply is normal, or call the plumbing.
- When the door is loosened, the command unit does not signal the start of the washing program, so water does not collect. Perhaps you just loosely covered the hatch. Other breakdowns can occur: failure of the sunroof lock device (UBL), breakage of the guide door or the handle itself. In this case, you will need to replace one of these elements. You can carry out repairs yourself - for this you just have to find the instructions and see how to remove the UBL or disassemble the door to replace the handle or guide.
- A clogged filter installed on the inlet hose may also block the flow of water into the tank. To clean the filter, you need to close the water supply valve on the pipe, disconnect the hose in the place of its attachment to the washing machine body, remove the filter with a pair of pliers and rinse it. Inspect the hose at the same time, it may also be clogged.
Euronov’s machine stopped, picking up water
The reasons that your washing machine stopped the washing program (while there is water left in it) may be such malfunctions:
Euronova does not heat water
This is not the most frequent breakdown for this brand, but it is not excluded due to the high hardness of the water in our plumbing systems.
Important! This is a critical error. As a rule, it arises due to the fact that the heater is overgrown with scale, because of which heat does not enter the tank. As a result, the heater overheats and burns out.
Short circuit possible! Disconnect the machine until you locate the breakdown.
Usually, in this situation, disassembling the washing machine, checking the thermoelectric heater with a tester and its subsequent replacement is necessary. Replacing the heater in the Euronov typewriters is not much different from the similar repair of typewriters of other brands.
SMA Euronova overheats water
As a rule, overheating of water in Eurosob or Euronov cars occurs for a number of reasons:
- The thermistor (temperature sensor) is out of order. The solution is to replace the sensor. The sensor is built into the heater, so when replacing it is possible to clean the heater from scale at the same time.
- The thermostat is broken or malfunctioning. Replacement is also required.
- Shorted the wires between the control module and the thermostat. It is necessary to solder contacts.
- Software crash. It can only be reprogrammed, repaired or replaced by an electronic module.
The first thing you can do yourself: check if you accidentally set the heating mode to “Boiling” or did not choose a program in which washing is carried out at 95 degrees.
Euronova's washing machine does not work at all
If the machine does not work, then trouble codes do not always appear. This is a difficult situation for the user, because it is not clear what caused the work to stop and what to repair.
The causes can be determined by the signs accompanying individual malfunctions:
- The machine does not respond to pressing the start button "ON". In this case, the wash lamp may light up, but the process does not start.
- Complete lack of response to the “ON” button, while the power indicator does not light up.
- If the indicators and numbers flash in a chaotic manner, this confirms the problem.
As a result, several breakdowns can be diagnosed:
- Failure of the "START" button.
- An open in the electrical circuit of the washing machine.
- Software failure, control board failure.
You can do the following yourself:
- Check if your machine is plugged in.
- Check that the power cord, plug and socket are working. To check the latter, use a screwdriver with an indicator or a working electrical device.
If all of the above is in order, a serious repair is needed - soldering or replacing the start button, restoring the integrity of the internal wiring of SM Euronov, or maybe even repairing or replacing the electronic module.
Possible damage according to the manufacturer
If you have lost the instruction manual, we will inform you of the possible damage listed in the user manual. The manufacturer is sure that these malfunctions occur in Euronov's cars most often:
- The drum does not rotate and functions are not performed. This may be due to the fact that there is no power supply, the hatch door is not tightly closed, the program has not been selected, or the selector ring is in the “0” position.
- The machine does not wring. The first reason: the laundry got stuck in a big lump, because of which the spin is blocked. The second reason: you set the “Wash without spin” mode.
- The powder does not enter the tank (or does not get out of the cell to the end). Perhaps you have chosen the program incorrectly, or the powder has strayed into lumps.
- The machine does not wash the laundry. The first possible causes are too much or too little powder, the temperature or program has been selected incorrectly.
- The machine is tearing linen. Often this happens due to the ingress of foreign objects into the tank.
Adhering to the rules of operation, you can avoid and prevent most of the crashes and breakdowns of the Euronov machine.