Buying new equipment is a joyful event. But so that this joy is not overshadowed by malfunctions, the first start of the washing machine must be approached with all responsibility. There are a number of rules that must be followed.
First launch step by step
Regardless of the brand of the washing machine, preparations are carried out before the first wash. The life of the machine depends on the correct connection and first start-up. If you are not at all versed in technology, it is better to call a qualified specialist.
Attention - instructions!
Each washing machine is equipped with instructions. In it, the manufacturer describes in detail the features of the technique and the rules for its operation. Including in the booklet there is information about the first launch. Different models of machines have their own subtleties in work. Therefore, before using the machine for the first time, it is important to carefully read the entire manual, including footnotes.
Connection check
So, your brand new washing machine is unpacked and connected. But do not rush to turn it on and start washing. First, check if everything is connected correctly. Even if the master was engaged in installing the device, the human factor cannot be ruled out. An absurd mistake can lead to breakage.
- Make sure that the rubber pipe is connected to the outlet of the water supply.
- The drain hose runs into a siphon or sewer pipe. Temporarily it can be lowered into the sink or bathtub, be sure to fix it on the edge. Otherwise, under the pressure of water, it will fly off - and the flood will be provided.
- Check if the bolts securing the drum are twisted. They are located on the outside on the back of the device. You can dismantle them yourself by unscrewing and inserting the plugs that come with the machine. If this is not done, the washing machine will vibrate violently and rattle, it may even break.
- Make sure that the machine is level and not staggering. When installed on a curve or soft surface, it will shake and move, which will negatively affect its work.
Machine inspection
The new machine is always carefully packed so that during transportation and storage at the warehouse nothing will deteriorate or break.
Packaging materials must be completely removed before the first start-up. Inspect:
- powder containers;
- Luke;
- drum;
If you find tape or foreign objects, be sure to remove them before starting.
Start
The preparation is over. Now you can start the washing machine for the first time.
New technology is coated with lubricants. It is also tested at the factory, and inside it may remain the remains of process water. Therefore, during the first washing, the laundry is not loaded. First, the machine should work out a full cycle idle.
- Plug in the washing machine.
- Load half a scoop of detergent into the main container.
- Leave the tank empty.
- Close the hatch.
- Choose the longest program with a temperature of at least 40 degrees.
- Click "Start."
Control
During the first cycle, it is important to stay nearby. If something goes wrong (extraneous sounds, flow), you must immediately stop the machine and disconnect it from the power. Do not try to fix the malfunction yourself.
A new washing machine is under warranty. You will be repaired or replaced for free. But only if no traces of an autopsy and self-repair attempts are found.
Pay attention to how the machine works:
- Does the drum slow down during washing and accelerate during spin?
- After water injection, how long does the machine heat it (normally - 5-7 minutes)?
- Is there a water leak at the hatch, under the machine, at the hose attachment point?
- Does draining work during spinning?
- Are there any extraneous sounds (rattle, rattling, knocking), strong vibration during the operation of the machine?
Means for the first start of the washing machine
To clean the washing machine of lubricants, it is enough to use half the dose of washing powder. It should be a powder for automatic washing, not manual. The latter gives a lot of foam, which is contraindicated to the machine. Powders for washing machines contain defoamers.
In addition, there are special tools for the first launch of washing machines - in the form of powder or tablets. They not only effectively clean all parts and seals, but also eliminate odors. They are inexpensive and can be used to clean the machine in the future, after 3 months of service or more.
Features of use:
- A special product is loaded into the powder compartment, less often into the drum (see information on the package).
- No need to load laundry!
- Any program with a temperature of 40 degrees and a duration of 1 hour is selected.
Names of special tools
The first washing tablets or powder are often offered to be purchased with a new washing machine in household appliance stores. Also, special tools can be found in the department of household goods and household chemicals. Names:
- Topperr 3217. A universal tool for the first launch of washing and dishwashers. Effectively dissolves oils and other undesirable components. It is odorless. Weight - 90 g (for one cycle). Approximate cost - 250 rubles.
- Magic Power MP-843. A low-cost tool that does an excellent job cleaning new washing machines. Its cost is only 170 rubles. Weight - 50 g (for one wash). The powder works at a temperature of 40 degrees.
- HELFER start. Means for the first start-up and preventive cleaning of washing machines. Removes odors, lubricants, oils, soot, soot, kills bacteria. For cleaning, the contents of the can are poured into the drum and the program “Cotton, 60 degrees” is selected. The average price is 200 rubles.
The first launch of a new washing machine can be exciting. But essentially it’s nothing complicated. It is only necessary to choose the longest program with a temperature of 40-60 degrees and leave the drum empty. The “idle” wash is aimed at washing off the remnants of technical fluids and checking the operation of the device. After that, the machine can be used as usual.